maxi dress tutorial

Yeah, I finally have the tutorial for the super easy maxi dress. 

Before we get started, I have to first thank Jess, from Craftiness is not Optional.  Not only has she given me the motivation to sew for myself, she also has a great tutorial for a raglan tee that helped make this possible. 

I really love wearing this dress. It is unbelievably comfortable. 

The raw edges and elastic thread made it super simple to put together.

I kept it plain so I could wear it lots of different ways. 

What you need:
2 yards of knit fabric (60" wide) or 4 yards (30"+ wide)
(you may need wider or longer if you are taller or wider than me.)
elastic and regular thread to match
preferably a serger, but you could try it with a zig zag stitch.
rotary board, ruler and cutter.

for the pattern:
a good fitting t-shirt
pencil
rotary ruler
freezer paper or wrapping paper

Step one: Make your pattern

Take a good fitting t-shirt and turn it inside out. Pull one of the sleeves inside itself and pin. Then with t-shirt folded in half trace around the edges the best you can.

Using your ruler draw a line from the armpit to the middle of the neckline.

Next line up your ruler with the shoulder seam and draw a new sleeve.

It should look something like this. I also re-drew the side seam so it gradually came down from the armpit and away from the body.
*I only cut a pattern for the bodice and sleeve of the dress.*

After I cut it out, it looked like this.

Step 2: cut out your pieces
This is probably the most difficult and nerve-racking part.  It is easier if you have someone helping you, but I was able to do it on my own.

My fabric was 60" wide and I wanted the front and back to each be 30" wide at the bottom. So I found the middle of the fabric and folded in one side at a time. I pinned down my bodice on the fold at the top and marked the length I wanted it to be on the bottom with a pin. (I cut it out to be longer than I wanted so I could have some wiggle room. I cut the excess off later.)

I cut out my bodice and continued cutting down the side with my ruler angled at the pin marking the bottom. When I got to the edge of my cutting mat I slid it down, being careful not to pull on the fabric. 

Cut a front, back and two sleeves.

Step 3: Sewing it together
The worst is over and the rest is a breeze.

Pin and serge the sleeves to the front body piece (right sides together). Next, sew the sleeves to the back piece.

Once the sleeves are on, serge up the armpit and down both sides.

Step 4: make adjustments
Try on the dress at this point and figure out if you need to make adjustments.

I wanted my neckline a little lower, so I cut that. The other adjustment I made was cutting some length off the bottom of the dress. One of your bottoms might be longer than the other, just cut them to be even.

Step 5: add elastic thread around the neck and sleeves
Don't be scared, it's really easy. You can buy elastic thread in the notions department. It comes in black, white and I think navy. Hand-wind the elastic into your bobbin and sew like normal. I sewed a zig-zag on the longest length I could. I sew two seams around the neck and one around the sleeve. You may need to play with your bobbin tension. If you have a brother machine you might want to read this tutorial. Practice on a scrap before starting.

Don't panic when you are done and the neck is itty bitty like this.  It will stretch and elongate with gravity once it is on.

See, no big deal.

(Optional) Step 6: sew waist line
I didn't sew a waist line on my dress because I wanted to be able to wear it with different belts. We did sew one on my sisters dress though.

While wearing the dress we marked were she wanted the waist line to go. After taking it back off, we drew a straight line all the way around the dress using a chalk pencil and the ruler.
Then, we sewed over the line with the elastic thread. We did two rows.

That's it, let me know if I left anything out or if you have any questions.